Document Show CAT Professional Jump-Starter Instruction
ManualCAT Professional Jump-Starter Instruction Manual SAVE THIS MANUAL FOR FUTURE REFERENCE. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment. This Class B digital apparatus complies with Canadian ICES-003. GENERAL SAFETY WARNINGS AND INSTRUCTIONSREAD ALL INSTRUCTIONS WARNING SAFETY GUIDELINES /
DEFINITIONS CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property damage. RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are certain applications for which tools and equipment are designed. Manufacturer strongly recommends that this product NOT be modified and/or used for any application other than for which it was designed. Read and understand all warnings and operating instructions before using any tool or equipment. IMPORTANT SAFETY INSTRUCTIONSWARNING: This product or its power cord contains lead, a chemical known to the State of California to cause cancer and birth defect or other reproductive harm. Wash hands after handling.
SPECIFIC SAFETY INSTRUCTIONS FOR CHARGING THIS UNIT
When an extension cord is used, make sure that: • a) the pins of extension cord are the same number, size and shape as those in the charger, • b) the extension cord is properly wired and in good electrical condition, • c) the wire size is large enough for the AC rating of the charger. CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE: Pull by the plug rather than the cord when disconnecting the extension cord from the built-in charging adapter or from the AC outlet. SPECIFIC SAFETY INSTRUCTIONS FOR COMPRESSORS WARNING: BURST HAZARD:
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE: Do not operate compressor continuously for longer than approximately 10 minutes, depending on ambient temperatures, as it may overheat. In such event, compressor may automatically shut down. Turn off the compressor power switch immediately and restart after a cooling down period of approximately 30 minutes. SPECIFIC SAFETY INSTRUCTIONS FOR JUMP STARTERS
SPECIFIC SAFETY INSTRUCTIONS FOR INVERTERS WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK: FIRST AID
INTRODUCTIONCongratulations on purchasing your new Cat® Professional Jump Starter. Read this Instruction Manual and follow the instructions carefully before using this unit. CHARGING/RECHARGINGLead-acid batteries require routine maintenance to ensure a full charge and long battery life. All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. Therefore, batteries need periodic charging to replace energy lost through self-discharge. When the unit is not in frequent use, manufacturer recommends the battery be recharged at least every 30 days. Notes: This unit is delivered in a partially charged state – you must fully charge it upon purchase and before using it for the first time for a full 40 hours or until the green LED Battery Status Indicator lights solid. Recharging the battery after each use will prolong battery life; frequent heavy discharges between recharges and/or overcharging will reduce battery life. Make sure all other unit functions are turned off during recharging, as this can slow the recharging process. In some rare cases, if the battery is overly discharged and the green LED lights immediately when the charger is plugged in, this indicates the battery is at a high impedance stage. If this occurs, recharge the unit for a period of 24-48 hours before use. CAUTION: RISK OF PROPERTY DAMAGE: Failure to keep the battery charged will cause permanent damage and result in poor jump starting performance. Charging/Recharging Using the 120 Volt AC Charger and a Standard Household Extension Cord (not included) 1. Open the AC adapter cover located on the back of the unit and connect an extension cord to the unit. Plug the other end of the cord into a standard 120-volt AC wall outlet. 2. Charge until the green LED Battery Status Indicator lights solid. 3. Once fully charged, disconnect the extension cord. Notes: The unit cannot be overcharged using this method. The unit will not charge if the compressor power switch is turned on. JUMP-STARTERThis Jump-Starter is equipped with an On/Off power switch. Once the connections are properly made, turn the switch on to jump-start the vehicle.
WARNING: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
120 VOLT AC PORTABLE POWER SUPPLYThis unit has a built-in Power Inverter that provides up to 200 watts of AC power. This inverter is an electronic device that converts low voltage DC (direct current) electricity from a battery to 120 volts AC (alternating current) household power. It converts power in two stages. The first stage is a DC-to-DC conversion process that raises the low voltage DC at the inverter input to 145 volts DC. The
second stage is a MOSFET bridge stage that converts the high voltage DC into 120 volts, 60 Hz AC. Power Inverter Output Waveform The AC output waveform of this inverter is known as a modified sine wave. It is a stepped waveform that has characteristics similar to the sine wave shape of utility power. This type of waveform is suitable for most AC loads, including linear and switching power supplies used in electronic equipment, transformers, and small motors.
Rated Versus Actual Current Draw of Equipment Most electrical tools, appliances, electronic devices and audio/visual equipment have labels that indicate the power consumption in amps or watts. Be sure that the power consumption of the item to be operated is below 200 watts. If the power consumption is rated in amps AC, simply multiply by the AC volts (120) to determine the wattage. Resistive loads are the easiest for the inverter to run; however, it will not run
larger resistive loads (such as electric stoves and heaters), which require far more wattage than the inverter can deliver. Inductive loads (such as TVs and stereos) require more current to operate than do resistive loads of the same wattage
rating.
MPORTANT NOTES: The Inverter Power/Fault Indicator is located inside the Translucent Inverter/USB Power Button. It will light solid blue when the unit is functioning properly and flash blue to indicate that one of the above fault conditions is present before automatic shutdown occurs. Should this occur, take the following steps:
Using the 120 Volt AC Outlet The 120 volt AC outlet outlet supports a maximum power draw of 200 watts.
Notes: The Inverter will not operate appliances and equipment that generate heat, such as hair dryers, electric blankets, microwave ovens and toasters.Some laptop computers may not operate with this inverter. Make sure the Translucent Inverter/USB Power Button is pressed to turn the inverter off (the Inverter Power/Fault Indicator is not lit) when the unit is not in use, being recharged or stored. Recharge this unit fully after each use. USB POWER PORT1. Press the Translucent Inverter/USB Power Button to turn on the USB Power Port. The Inverter Power/Fault Indicator will light blue to indicate the 120 volt AC outlet and USB Power Port are ready to use. 2. Plug the USB-powered device into the USB Charging Port and operate normally. 3. Periodically press the battery power level pushbutton to check battery status. (When all three battery status LEDs light, it indicates a full battery. Only one red battery status indicator light indicates that the unit needs to be recharged.) Notes: This unit’s USB Power Port does not support data communication. It only provides 5 volts/2,000mA DC power to an external USB-powered device. Some USB-powered household electronics will not operate with this USB port. Check the manual of the corresponding electronic device to confirm that it can be used with this type of USB port. Not all mobile phones are provided with a charging cable, they are normally data cables which are not supported by this device – please check with your mobile phone manufacturer for the correct charging cable. IMPORTANT: If the USB Power Port is not powering the device, turn the USB Power Port off and then on again using the Translucent Inverter/USB Power Button to reset the USB port. Make sure the appliance being powered does not draw more than 2,000mA. Make sure the Translucent Inverter/USB Power Button is pressed to turn the USB Power Port off (the Inverter Power/ Fault Indicator is not lit) when the unit is not in use, being recharged or stored. 12 VOLT DC PORTABLE POWER SUPPLYThis portable power source is for use with all 12 volt DC accessories equipped with a male accessory outlet plug and are rated up to 5 amps.
PORTABLE COMPRESSORThe built-in 12 volt DC compressor is the ultimate compressor for all vehicle tires, trailer tires and recreational inflatables. The compressor hose with tire fitting is stored in a retaining channel on the back of the unit. The On/Off Switch is located on the rear of the unit under the air pressure gauge. The compressor can operate long enough to fill up to 3 average sized tires before the battery must be recharged. The compressor may be used by removing the air hose from the storage compartment and if required, fitting an appropriate nozzle to the air hose. Return hose to the storage compartment after use. Inflating Tires or Products With Valve Stems
Inflating Other Inflatables Without Valve Stems Inflation of other items requires use of one of the nozzle adapters.
LED AREA LIGHTThe LED area light is controlled by the Area Light power switch on top of the light. Make sure the area light is turned off when the unit is being recharged or stored. Periodically press the battery power level pushbutton to check battery status. (When all three battery status LEDs light, it indicates a full battery. Only one red battery status indicator light indicates that the unit needs to be recharged.) TROUBLESHOOTINGProblem SolutionUnit will not charge
CARE AND MAINTENANCEAll batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When the unit is not in use, we recommend that the battery is charged at least every 30 days. Never submerge this unit in water. If the unit gets dirty, gently clean the outer surfaces of the unit with a soft cloth moistened with a mild solution of water and detergent. There are no user-replaceable parts. Periodically inspect the condition of adapters, connectors and wires. Contact manufacturer to replace any components that have become worn or broken. Battery replacement/disposal BATTERY REPLACEMENT The battery should last the service life of the unit. Service life is dependent on a number of factors including but not limited to the number of recharge cycles, and proper care and maintenance of the battery by the end user. Contact manufacturer for any information you may need. SAFE BATTERY DISPOSAL Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be disposed of properly. Recycling is required. Failure to comply with local, state and federal regulations can result in fines, or imprisonment. Please recycle. WARNINGS:
ACCESSORIESRecommended accessories for use with this unit are available from the manufacturer. If you need assistance regarding accessories, please contact manufacturer at 855-806-9228 (855-806-9CAT). WARNING: The use of any accessory not recommended for use with this appliance could be hazardous. SERVICE INFORMATIONWhether you need technical advice, repair, or genuine factory replacement parts, contact the manufacturer at 855-806-9228 (855-806-9CAT). ONE-YEAR LIMITED WARRANTYThe manufacturer warrants this product against defects in materials and workmanship for a period of ONE (1) YEAR from the date of retail purchase by the original end-user purchaser (“Warranty Period”). If there is a defect and a valid claim is received within the Warranty Period, the defective product can be replaced or repaired in the following ways: (1) Return the product to the manufacturer for repair or replacement at manufacturer’s option. Proof of purchase may be required by manufacturer. (2) Return the product to the retailer where product was purchased for an exchange (provided that the store is a participating retailer). Returns to retailer should be made within the time period of the retailer’s return policy for exchanges only (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges. This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from normal wear and tear, accidents; damages sustained during shipping; alterations; unauthorized use or repair; neglect, misuse, abuse; and failure to follow instructions for care and maintenance for the product. This warranty gives you, the original retail purchaser, specific legal rights and you may have other rights which vary from state to state or province to province. Please complete the Product Registration Card and return within 30 days from purchase of the product to: Baccus Global LLC, toll-free number: 855-806-9228 (855-806-9CAT). SPECIFICATIONS
Imported by Baccus Global, LLC,, 595 S. Federal Highway, Suite 210, Boca Raton, FL 33432 www.Baccusglobal.com • Toll-free: 855-806-9228 (855-806-9CAT) or International: 561-826-3677 RD030315 ©2014 Caterpillar. CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow,” “Caterpillar Corporate Yellow,” the “Power Edge” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission. Baccus Global, a licensee of Caterpillar, Inc. Baccus Global, LLC, 595 S. Federal Highway, Suite 210, Boca Raton, FL 33432 www.Baccusglobal.com FAQSLed light is all the time how to turn off Led stays on when charging, when fully charged press power button twice and led will go off within a couple seconds. Will it run a sump pump during a power outage? The 120VAC outlet on this jump starter is rated at 200watts maximum output. Which will run about 30 minutes to 1 hr at the maximum wattage draw and state of battery charge on the jump starter and age/number of charge cycles on internal battery. How do you recharge it? Plug into an electrical outlet to recharge. Is there a compartment to store the plug that charges this unit? No. just use a Velcro strip and attach it to the handle How many nights will this operate a cpap machine? Suspect if could run 1 entire night, NOT worth trusting safety and medical health to this machine.
It will charge it numerous times. Battery last a long time. How can you charge this with a solar panel? Plug panel into charge controller, controller to inverter plug jump box into inverter. Solar panels are DC jump box requires AC to charge. Want to power paddle board air pump. Is there a way to hook up a 12v cigar lighter socket power outlet socket receptacle? No, there is no 12v cigar receptacle. Can the tire inflator be used while it’s being charged? Even when the unit is low on charge? No is internal battery replaceable in CAT? It can be done because the battery inside is standard sealed lead acid battery, but there are no instructions on how open this up to get at the battery. Can this be taken in an airplane? no. How long does this take to charge? The instruction manual says: How much time can it run a 200w small heater? No more than 5 minutes Can ot Jumpstart a motorcycle Yes it can…. But you should be careful as you can overload the motorcycles electrical system will this start a dodge ram 1500 v8 truck This unit is a 12v battery charger. It will help start anything that depends on a 12v battery. How many hours will this last charging a phone? Or a fan? Etc Tested a medium size fan. Fully charged it ran for almost and hour. How much time can it run a 200w small heater? No more than 5 minutes will this power a tv? Look at UL tag on Tv to see wattage required to operate Tv, if over jump box inverter output, no, if under wattage output, of jump box yes, for a limited amount of time. How do I charge my cat jump starter?How do I charge my cat jump starter? Open the AC adapter cover located on the back of the unit and connect an extension cord to the unit. Plug the other end of the cord into a standard 120-volt AC wall outlet. Charge until the green LED Battery Status Indicator lights solid.
How do you charge a battery jump starter?We recommend charging your battery booster packs before going on a long trip. Usually an indicator light on the jump starter tells you when a recharge is necessary. Simply insert the power adapter into an outlet and charge the battery until the light indicates a complete charge.
How long does cat jump starter battery last?How often do I need to recharge my jump starter? Typically as a general rule 24 - 48 hours immediately after purchase and after every use. It is also recommended to recharge every 30 - 60 days for approximately 12 hours or until the battery status indicators show full when the product is not in use.
|