What grit sandpaper for wet sanding Car paint

Q: What grit sandpaper is safe for car paint?

1,500 grit is a good starting point, though youll need to be cautious about sanding it off too much. Its better if you have 2,000 grit, at least, as you can then move up and up to 2,500 grit, and the final 3,000 grit for an ultra-fine finishing touch.

Q: What grit sandpaper should I use to wet sand paint?

What Grit Sandpaper Should I Use? When youre first beginning to wet sand your material, youll want to start with a grit between 600 and 1,200. Once you choose your starting grit, youll follow dry sanding standards to increase the by 200 to 500 grits per pass to get the finish you want.

Table of Contents Show

What is the best sandpaper for wet sanding a car?
What grit sandpaper is safe for car paint?
What grit sandpaper should I use to wet sand paint?
Is 2000 Grit good for wet sanding?

“What sandpaper grit should I use?” is one of the most popular questions on every auto forum. It is important to choosing the right sandpaper grit for each task to avoid paint damage. There are a lot of different contradictory information online that can be very confusing and overwhelming especially for beginners who have never done any repair projects before.

After reading some of the posts, I found out that a lot of car enthusiasts are using the wrong grit. I saw some people were saying that they’ve used 600 grit or even 400 grit sandpaper to repair clear coat scratches. Big mistake! Sandpaper lower than 1,500 grit is too rough for the clear coat and will leave small scratches.

Sandpaper “grit” refers to the number of abrasive particles per square inch of sandpaper. The lower the grit number, the rougher the paper. The grit use depends on your repair project. For tough jobs, like stripping the paint, you would need lower grit sandpaper and conversely, for clear coat repairs you would use higher grit sandpaper.

40 – 80 Grit

I use 40 grit for very rough sanding/grinding before doing the bodywork. This is very course sandpaper that will leave rough sanding marks. So, use it only when you really need it like for removing rust or on very deep scratches before applying body filler/bondo.

80 grit works great for shaping body filler. Of course a lot depends on the quality of the body filler. The better the quality the easier it will be to sand. If you are using a cheap filler, it will take you a while to sand it. So, start with a 40 grit, then 80 grit and to even it out 120 grit.

120 – 180 Grit

120 grit is not as rough and is great for flattening out scratches from heavier grit. 180 grit is great for feathering edges of the body filler and sanding the spot putty. 180 grit can also be used to remove light rust with minimal scratching

320 – 400 Grit

Both grits are usually used for sanding before primer. 320 grit is great for final sanding of body filler or spot putty. 400 grit will work for fine sanding spot putty and for rough sanding a primer although, I prefer 600 grit for that. In this step, the goal is to make the surface as flat and as smooth as possible before primer application. Every little imperfection will get magnified once the paint is applied. With this in mind, you want to spend most of your time preparing the surface.

To avoid waves and finger prints, use a sanding block. Block sanding is when you wrap the paper around a backing pad or a block. It will help you evenly distribute hand pressure across the sandpaper making it easier to sand curved surfaces. Always sand using “X” pattern. Also, avoid spending too much time on one spot.

600 – 800 Grit

600 grit and 800 grit are used for sanding imperfections in the primer before applying the base coat/paint. Start with 600 grit and work your way up to 800 grit.

1000 – 1,200 Grit

You can use 1,000 grit or 1,200 grit over the base coat to remove imperfections. It is important to use “wet sanding” technique. Wet sanding is when you soak the sandpaper and spray the surface with a lot of water. I usually add few drops of dish soap to make it more slippery. I find that “wet sanding” cuts faster and doesn’t clog the sandpaper. Wrapping the sandpaper around the block will help to make sanding more even.

Even though the 1,200 grit is a fine sandpaper, it will still leave scratches that should be removed with 1,500 or 2000 grit before applying clear coat.

1,500 – 2,000 Grit

1,500 grit and 2,000 grit are used to sand the clear coat. Both grits are great for removing light clear coat scratches that can’t be removed by rubbing compound and buffing. Use 2,000 grit for final sanding to achieve smooth surface.

When working with these grits, don’t forget to use wet sanding method for better result. Soak the sandpaper in cold water for about 10-15 min. Wrap it around a block or backing pad. Spray the repair area with water to keep it slippery. Also adding few drops of dish soap to the water will help. Wash off sandpaper after 3-4 sweeps to avoid dust getting in the way. Keep checking the surface with your fingers.

Note: For small projects you can get an assorted pack of 5 sheets of sandpaper while for bigger projects you will need to buy each grit separately.

Rubbing compound

Rubbing compound is not a sandpaper and doesn’t have a grit number, but it also removes imperfections in the clear coat and smooths the surface after 2,000 grit. Since paint might be a little dull after sanding, rubbing compound is also used to bring back the shine. My favorite is Meguiar’s Ultimate Compound. You can do buffing by hand or use an electric polisher. I personally like to use Meguair’s Dual Action Polisher because it does an amazing job and is very easy to use even for beginners.

Please let me know if you have any questions.

~Mike Davis

P.S. If you like this article, please help me promote it by clicking “Like” button below.

What is the best sandpaper for wet sanding a car?

The Process Of Wet Sanding A Car If we are repairing minor damage or wet sanding a new automobile, use 2000 or 3000 grain sandpaper. To remove deep scratches, use sandpaper with 1200 or 1500 grit.

What grit sandpaper is safe for car paint?

1,500 grit is a good starting point, though you'll need to be cautious about sanding it off too much. It's better if you have 2,000 grit, at least, as you can then move up and up to 2,500 grit, and the final 3,000 grit for an ultra-fine finishing touch.

What grit sandpaper should I use to wet sand paint?

What Grit Sandpaper Should I Use? When you're first beginning to wet sand your material, you'll want to start with a grit between 600 and 1,200. Once you choose your starting grit, you'll follow dry sanding standards to increase the by 200 to 500 grits per pass to get the finish you want.

Is 2000 Grit good for wet sanding?

Be sure to use the wet sanding technique for best results. 1500 to 2000 Grit – When you need to smooth out surface imperfections and scratches before and after applying the clear coat, this is the grit range to use. This will also require the wet sanding technique to prevent clogging the sandpaper.