One of the most useful tools in a tradesman's toolbox is the common tape measure. Let's see how to read a tape measure.
The tape measure can be marked with US or English measurements (feet and inches), metric measurements (meters and parts of meters: centimeters, millimeters, etc) or both shared on the same tape. Most tape measures have common elements to be able to use them easily. Most US tape measures have both inches and foot marks. Notice that the 16", 32", 48", 64", etc. are marked differently than the other inch markers. Some tape measures have small black arrows or pointers with a box around the number, other tape measures have these numbers highlighted in red. These numbers refer to the 16" centers for laying out studs and joists. Most carpenters have the 16" centers memorized up to 8', but a little help on the tape measure is well received when you get to 128". As well as the 16" marks, notice a black diamond mark every 19.2 inches, also called the black truss mark. It was put on the tape measure originally to designate the on-center position of residential roof trusses. Rather than placing 6 trusses in 8', every 16", they saved a truss every sheet of plywood by spreading them out. We don't use this position today with our trusses, which are commonly designed for 24 inch centers.
When you read a tape measure a little knowledge of math is needed. We know that 1/2 is the same as 4/8, 8/16, 16/32, etc. We could refer to the 1/2" mark as the 16/32" mark but we usually use the simplest numbers possible. Since we know that 16/32 is 1/2, when looking for 15/32" on the tape measure, for example, it is the first 32nd before the 1/2" mark.
Actually, in the field a carpenter refers to a 32nd as plus or minus a major fraction. For instance, 13/32 is 1/32 less than 14/32 or 7/16, so we say "7/16 minus" and 11/32 is 1/32 more than 10/32 or 5/16, so we say "5/16 plus". This is a fast way of reading the tape measure on the job when taking a measurement of something to cut it to fit. What you should do is memorize the common fractions down to sixteenths.
Here they are:
1/16, 1/8, 3/16, 1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16 and the inch mark.
How to Read a Tape Measure
We use thirty-seconds in the stair calculator, and other instances like that, just for accuracy because when you're cutting 16 stair risers, if you are 1/16th inch out on each stair, you are out a whole inch at the end. Even being 1/32" out gives an error of 1/2"!
Here is a video I made with Dan's help (my brother and webmaster).
Dave
(Ask Dave) (About Dave)
Here we will explain and show you where 1 9/16 inches is on a ruler. More specifically, we will give you step-by-step instructions on how to find, and then illustrate, where 1 9/16 is located on a ruler.
The ruler is divided up into whole inches: 1 inch, 2 inches, 3 inches, and so on. First, we will determine between which two whole inches 1 9/16 fits. 1 9/16 as a decimal is 1.5625, which is greater than 1 and less than 2. Therefore, 1 9/16 is located between 1 inch and 2 inches on the ruler.
If you look closely at a ruler, you will see that there are 15 marks between each inch, dividing each inch into 16 equal parts. Below are the lengths to each mark from any whole inch:
Mark 1: 0.0625
Mark 2: 0.125
Mark 3: 0.1875
Mark 4: 0.25
Mark 5: 0.3125
Mark 6: 0.375
Mark 7: 0.4375
Mark 8: 0.5
Mark 9: 0.5625
Mark 10: 0.625
Mark 11:
0.6875
Mark 12: 0.75
Mark 13: 0.8125
Mark 14: 0.875
Mark 15: 0.9375
Looking at the table above, we can locate where the decimal part of 1.5625 fits. The decimal part of 1.5625 fits exactly on Mark 9.
Now we have all the information we need to show you where on our ruler 1 9/16 is located. 1 9/16 is located between 1 inch and 2 inches on Mark 9. Our illustration below shows 1 9/16 inches marked with a red pin.
Inches on a Ruler
Go here if you want us to find another length in inches on a ruler.
1 9/17 inches on a ruler
Here is the next length in inches on our list that we have
illustrated on a ruler for you.
Copyright | Privacy Policy | Disclaimer | Contact