it really depends on the temperature around you
to be on the safe side, you could leave it overnight at room temp
you might be able to go at it a bit earlier though
i take it you will be wet flatting this - a good tip here is dust a darker colour on. like some blue or red or whatever you have kicking about.
just a fine dust layer though!
this is called a "marker". when wet flatting, keep going until the marker has all gone. that way you know you have got everywhere.
wrap your wet n dry paper around a bit of rag, that way you get plenty of water about the place.
level 1
· 7 yr. ago
You're a Gundam, he's a Gundam, everyone is a Gundam!
On a hot/warm day, Tamiya primers are often dry to the touch within several minutes, but I usually wait an hour or two before painting over it to make sure its really settled.
1
- Home
- »
- FineScale Modeler
- »
- Forums
- »
- Tools, Techniques, and Reference Materials
- »
- Painting and airbrushing
- »
- Tamiya Primer drying time?
- Order Ascending
- Order Descending
| Tamiya Primer drying time? Posted by espins1 on Sunday, September 24, 2006 7:29 PM Anyone know how long I need to wait after using Tamiya Primer to preshade and begin painting?
|
| Posted by Bgrigg on Sunday, September 24, 2006 9:38 PM Three to four weeks! Nah, only kidding. It's a synthetic lacquer so I would give it a couple of hours at the minimum and overnight because I don't work fast anyway. So long folks!
|
| Posted by espins1 on Sunday, September 24, 2006 10:08 PM heh heh..... I waited about 3 hours, pre-shaded and did the yellow nose on my Bf109E-7. Seems to have been enough time for the primer.
|
FREE NEWSLETTER
By signing up you may also receive reader surveys and occasional special offers. We do not sell, rent or trade our email lists. View our Privacy Policy.
Joined May 25, 2009 · 2,188 Posts
Discussion Starter · #1 ·
Jun 18, 2009 Since I can't read Japanese, how long should I let Tamiya Fine Surface Primer dry before applying paint? Joined
May 7, 2003 · 5,016 Posts
Thirty minutes. Unless you've laid it on really thick, in which case you may want to wait a bit longer.
Joined Oct 17, 2008 · 83 Posts
I would give it longer,. it also depends on the weather, a more humid day i would give it longer. i always do a spray out, meaning i spray a piece of scrap plastic and check that before i touch the model. just to be safe, dont want a big wet finger print on the surface because it was still wet. Al Joined
Oct 10, 2000 · 2,575 Posts
LOL! I had the same problem. I gave it two hours, just to be sure. No matter the conditions I've never had a problem after that length of time. Joined May 25, 2009 · 2,188 Posts
Discussion Starter · #5 ·
Jun 19, 2009 Thanks. It certainly seems completely dry after 2 hours. Was looking at my Testor's primer which has English instructions...bizarrely worded. They say: "To avoid possible wrinkling, recoat within 3 hours or after 48 hours." Also says "May be sanded after 2 hrs dry." Never once does it say something plain and simple like: "You can
paint what you primed after 3 hours."
Joined May 7, 2003
·
5,016 Posts
Humidity can certainly be a factor, but generally speaking I find I can sand and paint a primed surface within 30 minutes or so. Something I've been doing on a daily basis of late. I mean, there's certainly nothing wrong with waiting longer if you have the time, but my weekly modeling hours are few and precious and I don't like to waste them
waiting for primer to cure. If in doubt run a few tests and see for yourself. There's really no better way to develop a feel for the materials you're working with. BTW, FWIW, I've experimented with A LOT of primers, and unfortunately the Tamiya stuff remains my fave. I say "unfortunately" because it's much more expensive than most of the others I've tried.
Joined May 25, 2009
·
2,188 Posts
Discussion Starter · #7 · Jun 19, 2009
I live in Louisiana where the humidity is ALWAYS high so longer drying times are something I am going to have to live with. I like the Tamiya over the Testor's myself but, as you say, much more $$$$.